齒輪工業領域服務平臺,行業技術的領航者;
把齒輪傳動之脈搏,譜信息時代之新篇!
當前位置: 新疆十一选五怎么玩 » 技術中心 » 行業標準

新疆十一选五助手官网:數控機床常見報警信息中英文對照大全!

發布時間:2019-02-28 | 來源:互聯網 | 作者:
   平時在操作數控機床時,總會遇到報警的信息提示,有些英文的對照不免讓新學者頭疼,小編特意整理了一些常見的數控機床報警信息中英文對照版的,沒事翻翻就當小小工具書了!(僅供參考)

T WORD ERROR (T 碼錯誤)

LOW OIL LEVEL (油位低)

SPINPLE FAULT (主軸故障)

SPINDLE ALARM (主軸報警)

EXTERNAL EMG STOP (急停按鈕被按下)

AC NOT READY (交流盤未準備好)

SPINPLE LUBE FAULT (主軸潤滑故障)

T CODE ERROR (T代碼出錯,非法T代碼)

M CODE ERROR (M代碼出錯,非法M代碼)

SERVO NOT READY (伺服未準備好)

NC NOT READY(NC沒準備好)

TURRET FAULT (轉塔故障)

TURRET LIMIT (轉塔限位)

DC 24V OPEN (直流24斷開)

+24V NOT READY(+24V沒準備好)

GRAR DRIFT (檔位漂移)

PLEASE AXIS RETURN HOME(軸未回零)

PLEASE DRUM RETURN HOME(刀庫未回零)

AIR PRESSURE DROP (壓縮空氣壓力過低)

CLAMP TOOL FALL(夾刀失敗)

DRUM NOT PARKED(刀庫未在原值)

X ZERO POINT NOT REACHED (X 軸未回零)

Y ZERO POINT NOT REACHED (Y 軸未回零)

Z ZERO POINT NOT REACHED (Z 軸未回零)

4TH ZERO POINT NOT REACHED (第4軸未回零)

X AXIS OVERTRAVL(X軸超限)

Y AXIS OVERTRAVL (Y軸超限)

Z AXIS OVERTRAVL (Z軸超限)

COUNTER SWITCH REEOR (計數開關故障)

MASTERT RANSFER OVER TEMP (主變壓器過熱)

Z AXIS NOT AT FIRST REF POSITION (Z軸未在第一參考點)

SPINDLE ORIENTATION FALLURE (主軸定向失敗)

TOOL DESENT OR TOOL DATA REEOR (刀具數據錯誤)

PLEASE UNLOAD THE TOOL ON SPRINELK (請卸下主軸上的刀)

PLEASE LOAD TOOL ON APINDLE (請裝上主軸上的刀)

A AXIS UNCLAMP FAIL (A 軸松開失敗)

A AXIS CLAMP FAIL (A 軸夾緊失敗)

DRUM OUT TO APRONDLEIS FALL (刀庫擺向換刀位失敗)

MG SWING OVERLOAD(刀庫擺動過載)

DRUM BACK PARK IS FALL (刀庫擺回原始位失敗)

TURRENT MOTOR1 OVERLOAD (刀庫移動電機過載)

COOLANT MOTOR OVERLOAD (冷卻泵過載)

DRUM ATC FAULT (自動換刀失敗)

TOOLS UNLOCKED (刀具未鎖緊)

BATTERY ALARM (電池報警)

DRUM POSITION SWITCH ERROR (刀庫位置檢測開關故障)

DRUM NOW NOT AT PARK (刀庫未在原始位置)

IT DANGOU TO MOVE DRUM (刀庫禁動)

POT UO FAILOR POT NOT AT UP POSITION (刀套未在水平位)

POT DOWN FAIL (刀套翻下動作失敗)

IT IS DANGOUR TO MOVE ARM (機械手禁動)

THE SPINDLE STATU IS ERROR (主軸狀態錯誤)

ARM MOTOR OR ARM SWITCH FALL (機械手或機械手開關故障)

CENTRE LUBRICATION FALL (中心潤滑故障)

THE WORK NOT CLAMPED (工件未夾緊)

AUTO TOOL CHANGE FAULT (自動換刀失敗)

TOOL DATA OUT OF RANGE (指令刀具號超出范圍)

THE ORDER TOOL NOW IN SPINDLE (目標刀具在主軸上)

THE THREE SPINDLE SWITCH FAULT (主軸上的接近開關)

THE CENTRE COOLANT IS LOWER (刀具內冷泵液位過低)

DRUM RETURN 1# POSITION FAULT (刀庫自動回零失敗)

SPINDLE OVERLOAD (主軸過載)

TURRENT MOTOR OVERLOAD (刀盤轉動電機過載)

CHIP CONVEYER OVERLOAD (拉屑器過載)

HARD LIMIT OR SERVO ALARM (硬限位或伺服報警)

NO LUB OIL (無潤滑油)

INDEX HEAD UNLOCKED (分度頭未鎖緊)

MT NOT READY(機床沒準備好)

MG OVERLOAD (刀庫過載)

LUB EMPTY(潤滑無油)

AIR PRESSURE(氣壓不足)

COOLANT NOT READY(冷卻沒準備好)

LUBE EMPTY(油霧油位低,潤滑油位低)

LUB PRESSURE LOW(潤滑壓力低)

CONVEY VERLOAD(排屑過載)

LUB OVERLOAD(潤滑過載)

LUBE PRESSURE LOW(油霧壓力低)

SERIAL SPINDLE ALARM (串行主軸報警)

NC BATTERY LOW ALARM(NC電池低報警)

MAGAZINE MOVE LIMIT SWITCH ERROR

SPINDLE TOOL UNLAMP POSITION LIMIT SWITCH ERROR

MAGAZINE NOT IN POSITION OR SENSOR ERROR

AIR PRESSURE LOW ALARM(氣壓低報警)

MOTOR OVERLOAD(電機過載)

T CODE > MAGAZINE TOOLS

T CODE < 1 ERROR

5TH AXIS HARDWARE OVERTRAVER LIMIT ERROR

DOOR IS OPENED(開門)

LUB PRESSURE SWITCH ERROR(油壓開關錯誤)

SPINDLE OIL COOLANT UNIT ERROR

SPINDLE LOAD ABNORMAL(主軸負荷異常)

TRANSDUCER ALARM(傳感器報警)

BED-HEAD LUBRICATE OFF(床頭潤滑關閉)

EMG OFF太

HYDRAULIC CHUCK PRESS LOW(液壓夾頭壓力低)

HYDRAULIC TAIL PRESS LOW(液壓尾座壓力低)

LUB 0IL LOW(油壓低)

TURRET CODE ERROR(轉塔碼錯誤)

TURRET RUN OVERTIME(轉塔運行超時)

MANUAL HANDLE INTERRUPT

TRY TO RUN SPINDLE WHILE CHUCK NOT LOCK

TRY TO RUN SPINDLE WHILE TAIL NOT LOCK

SPINDLE NEUTRAL GEAR

MAGAZINE ADJUST

HYDRAULIC NOT RUN

SAFETY DOOR BE OPENED

SAFETY DOOR NOT CLOSE

NOT ALL AXIS HAVE GONE BACK REF

IN ADJUST,IGNORE GOING BACK REF

AFTER EXCHANGE TOOL,CYCLE START

ATC MOTOR QF16 OFF

X AXIS IS LOCKED(X 軸被鎖定)

Y AXIS IS LOCKED(Y 軸被鎖定)

Z AXIS IS LOCKED(Z 軸被鎖定)

A AXIS IS LOCKED(A 軸被鎖定)

SPINDLE MOTOR FAN QF26 OFF(主軸電機風扇QF26關閉)

關注我們的微信公眾號shukongzhpngguo,獲取更多數控技術文章。

SPINDLE ORIENTATION INCOMPLETE(主軸定位不完全)

M FUNCTION NOT COMPLETE(M 功能無法完成)

SPINDLE NOT IN GEAR POSITION(齒輪不在主軸位置)

SPINDLE NOT CHANGED TO LOW GEAR(主軸沒有變為低檔)

SPINDLE NOT CHANGED TO HIGH GRAR(主軸沒有變為高檔)

MAG NOT BACKWARD

SPINDLE TOOL NOT CLAMP

SPINDLE TOOL NOT UNCLAMP

MAG NOT IN POSITION

MAG DOES NOT ROTATE

MAG DOES NOT STOP RUNNING

A AXIS HAVE NOT CLAMPED

A AXIS HAVE NOT UNCLAMPED

SET D499=1,"MAG.JOG" SWITCH ON

HYDRAULIC MOTOR QF7 OFF( 液壓馬達QF7關閉 )

HYDRAULIC TEMPRETURE HIGH( 液壓使用溫度高 )

HYDRAULIC FILTER BLOCKED(液壓過濾器阻止)

HYDRAULIC OIL LEVEL LOW( 液壓油位低 )

HYDRAULIC FAN QF8 OFF(液壓風扇QF8關閉)

HELIX CONYER QF9 OR QF10 OFF

CHAIN CONYER QF11 OFF

COOLANT MOTOR QF12 OFF(冷卻液電機QF12關閉)

COOLNT LEVEL LOW,CYCLE STOP AFTER 20 MINUTES

INNER COOLANT BLOCK(內冷卻堵塞)

SPINDLE COOLANT MOTOR QF14 OFF(主軸冷卻液電機QF14關閉)

INNER COOLANT QF13 OFF(內冷卻液QF13關閉)

MAG MOTOR QF15 OFF

CABINET COOLANT EQUIP QF20 OFF

OIL GATHER QF24 OFF

AIR PRESSURE LOW(低氣壓)

SPINDLE COOLANT MOTOR FAULT(主軸冷卻液電機故障)

LUB.OIL IS LOW(潤滑油低)

DOOR OPEN(門打開)

FRONT DOOR(R) OPEN(前門打開)

LEFT DOOR OPEN(左門打開)

LUBRICATION OIL QF23 OFF(潤滑油QF23關閉)

LUBRICATION PRESS LOW(潤滑油位低)

IN ADJUST,MAG CAN'T EXCHANGE T(在調整,刀庫不能交換T)

NOT ALL DOOR CLOSED(門沒有全部關閉)

IN M06,MAG NOT READY(在M06,刀庫未準備好)

MAGAZINE NOT READY(刀庫未準備好)

POCKET NOT HORIZANTAL

IN M06,Z NOT BACK TO 2ND REF

IN M06,Z AXIS NOT IN PSW1

ATC NOT IN ZERO POSITION

SPINDLE ORIENTATION UNCOMPLETE

POCKET NOT HOR./MAG NOT BCKWRD

POCKET NOT VER./MAG NOT FORWRD

UNCLAMP TOOL HAS NOT COMPLETED

CLAMP TOOL HAS NOT COMPLETED

AIM TOOL NO. IS WRONG

MAG NOT BACKWARD

AFTER RETRACT,SET R.T.BACK OFF

Z NOT IN PSW2,FORBID ATC RUNNING

D499 EQUAL 1

MAG.JOG SOFT SWITCH IS ON

Z NOT IN PSW2,FORBID MAG FORWARD

CHEKE SPINDLE MODULE ALARM

OIL WATER SEPARATOR QF24 OFF

SET THE SOFT SWITCH MAG.JOG OFF

SET D499 TO 0 設定D499為0

K PARAM ABOUT MAG SET IS WRONG 關于MAG的K參數設定錯誤

MECHANICAL BRAKE NOT RELEASED機床抱閘沒有松開

MECHANICAL BRAKE IS WRONG 機床抱閘錯誤

PLEASE ADD LUB.OIL 請加潤滑油

PROBE BATTERY VOLTAGE IS LOW 探頭電池電壓低

PROBE IS ERR 探頭錯誤

PARAMETER WRITE ENABLE(參數寫使能)

PMC EDIT ENABLE(PMC編輯使能)

CHECK LUB ROUTIN

SPINDLE GEAR SIGNAL MISS 主軸檔位信號消失

T_CLAMPED_SIGNAL MISS T夾緊信號消失

SP OVERRIDE SWITCH DISCONNECTION 主軸倍率開關斷路

FEED OVERRIDE SWITCH DISCONNECTION 進給倍率開關斷路

THE TOTAL NUMBER OF POCKETS SET ERR

CHANGE T STOPED BECAUSE NO AIR 因為缺少壓空交換停止

THE COOLANT WATER TOO LOW,ADD COOLANT WATER AT ONCE 冷卻水少立即加水

COOLANT LEVEL LOW,ADD COOLANT WATER 冷卻水液位低

PLEASE REPLACE CNC BATTERY QUICKLY 請立即更換CNC電池

SIEMENS常用縮略語

A Output 輸出

ASCII American Standard Code for Information Interchange 美國信息交換標準代碼

AV Preparation for work 運行準備

BA Operating mode 運行方式

BAG Operating mode groups 運行方式組

BB Ready for operation 準備好運行

BCD Binary Coded Decimals 二-十進制

BHG Hand-held terminal 手提終端

BOF User interface 用戶接口

CNC Computerized Numerical Control 計算機化數字控制

CP Communication Processor 通迅處理器

CPU Central Processing Unit 計算機中央處理裝置

CR Carriage Return 托架折回

CSB Central Service Board(PLC module) 中央維護板,PLC ???br />
CTS Clear To Send 發送使能

DAU Digital-Analog Converter 數模轉換器

DB Data Block 數據塊

DIN German Industrial Standards 德國工業標準

DIO Data Input/Output 數據輸入/輸出

DRF Differential Resolver Function 差分功能

DRY Dry Run 空運行

DSB Decoding Single Block 譯碼單段

DSR Data Send Ready 備用輸入

DW Data Word 數據字

E Input 輸入

EIA-Code Special tape code,number of holes per characters always odd 特殊紙帶碼,每個字符的孔數為奇數

EPROM Programm memory with fixed program 有固定程序的程序存儲器

E/R Controlled Supply and Energy Recovery Module 可控電源和能量恢復???br />
ETC ETC key:Extension of the softkey bar in the same menu

ETC 鍵:同級菜單擴展鍵

FDB Product designation database 產品指定數據庫

FIFO First in First Out 先進先出

FRA Frame module 幀頻???br />
FRAME Coordinate conversion with the components zero

offset,rotation,scaling,

mirror-imaging 坐標換算,具有零點偏置,坐標旋轉,標度功能和鏡向功能

FRK Cutter radius compensation 銑刀半徑補償

FST Feed Stop 停止進給

GUD Global User Data 全體用戶數據

HMS High-Resolution Measuring System 高分辨率測量系統

HSA Main Spindle Drive 主軸驅動

HW Hardware 硬件

IM Interface Module 接口???br />
IM-S/R Interface Module(S=send/R=receive) 接口???,S=發送/R=接收

INC Increment 步進增量

ISO-Code Special tape code,number of holes per character always even

特殊紙帶碼,每個字符的孔數為偶數

K1...k4 Channel 1 to Channel 4 通道1 到通道4

KOP Ladder Diagram 梯形圖

KV Loop-Gain Factor 增益系數

KUE Transformation Ratio 傳動比

LCD Liquid Crystal Display 液晶顯示

LED Light Emitting Diode 發光二極管顯示

LUD Local User Data 局部用戶數據

MB Megabyte 兆字節

MD Machine Data 機床數據

MK Measuring Circuit 測量回路

MDA Manual Data Automatic 手動輸入,自動執行

MLFB Machine-readable product designation 機器可識別的產品代號

MMC Man Machine Communication:User interface of the numerical control

system for operation,programming and simulation 人機通訊:系統操作界面,用操作,編程和模擬

MPF Main Program File:NC part program(main program)

NC 零件程序,主程序

MPI Multi Point Interface 多點通訊接口

MSTT Machine control panel 機床控制面板

NC Numerical Control 數字控制

NCK Numerical Control Kernel(numerical krnel with block preparation,

traversing range etc.) 數字控制核心:具有程序段預處理,運行范圍等等

NCU Numerical Control Unit 數控單元

NURBS Non Uniform Rational B Spline 非均值有理B樣條

NV Zero Offset 零點偏置

OEM Original Equipment Manufacturer 原設備制造商

OP Operator Panel 操作面板

OPI Operator Panel Interface 操作面板接口

PC Personal Comprter 個人計算機

PCMCIA Personal Computer Menory Card International Association 接口協議

PG Programming Device 編程器

PLC Programmable Logic Control 可編程邏輯控制器

PRT Program Test 程序測試

RAM Random Access Memory 隨機存取存儲器

RISC Reduced Instruction Set Computer 處理器,具有指令組小、通過能力強

ROV Rapid Override 快速修調

RPA R Parameters Active(NCK memoty area for R parameter numbers)

R 參數有效,NCK 中用于R 參數號的存儲器區

RTS Request To Send(control signal from serial data interfaces)

發送請求:來自串行接口的控制信號

SBL Single Block 單段

SBL2 Single Block Decoding 譯碼單段

SEA Setting Data Active(memory area for setting data in NCK)

設定數據有效:用于NCK 中設定數據的存儲區

SD Setting Data 設定數據

SKP Skip Block 程序段跳躍

SM Signal Module 信號???br />
SPF Sub Program File 子程序文件

SPS Programmable Logic Controller 可編程邏輯控制器

SRK Cutter Radius Compensation 刀尖半徑補償

SSFK Leadscrew Error Compensation 絲杠螺距誤差補償

SSI Serial Synchronous Interface 串行同步接口

SW Software 軟件

TEA Testing Data Active(with reference to the machine data) 測試數據有效:與機床數據有關

TO Tool Offset 刀具補償

TOA Tool Offset Active(memory area for tool offset) 刀具補償有效,用于刀補的存儲區

TRANSMIT Transform Milling into Turning(coordinate conversion on

turning machines for milling)

銑床轉換為車床:車床坐標換算用于銑削加工

VSA Feed drive(spindle) 主軸進給驅動

V Bit type PLC variable PLC變量類型:位

VB Byte type PLC variable

PLC變量類型:字節

WKZ Tool 刀具

WZ Tool 刀具

WZK Tool offset 刀具補償

ZOA Zero Offset Active(memory area for zero offsets)

零點偏置有效:零點偏置存儲區
[ 技術中心搜索 ]  [ ]  [ 告訴好友 ]  [ 打印本文 ]  [ 關閉窗口 ]  [ 返回頂部 ]